Changed Motor Oil & Replaced Filter, Added REQUIRED QTS VALVOLINE SYNPOWER Motor Oil, Lube Chassis, Check all Fluid Levels
Rotate Tires. Visually inspect tires/brakes. NOTE!!!!! Custom Wheels (NON FACTORY WHEELS) MUST be Re-Torqued After 100 Miles to Manufacturer Specs! Beck Automotive is NOT Liable if Re-Torquing is not done by Beck Automotive Technicians (Complementary Re-Torquing)
Beck Automotive Courtesy Inspection
DOUG D. gave our service a 5 star review on 8/15/2022
Technician test drove and inspected. Rattle coming from exhaust hangers. Repaired and test drove- ok at this time.
Recommend replacing wiper blades front and rear. Front struts/rear shocks showing signs of wear/boots deteriorating. Tire light on. Pressure was low. Aired to spec. If light persists, could be sensor. Recommend replacing 2 tires 185/65R15
SHOCK &/OR STRUT ASSEMBLY – Remove & Install or Remove & Replace – Both – [DOES NOT include disassemble or alignment.]
SHOCK &/OR STRUT ASSEMBLY – Remove & Install or Remove & Replace – Both – [Includes: Bleed Brake System (where applicable). DOES NOT include disassemble or alignment (where applicable).]
Place vehicle on alignment rack, attach equipment, measure caster, camber and toe. Compare to vehicle specifications. Set and adjust all approved alignment angles with allowable specifications.
Mount and balance two tire/wheel assemblies.
TIE ROD &/OR END – Remove & Replace – Inner,Both – [Includes: R&I Outer Tie Rod Ends.] – [Includes: Adjust toe-in only. NOTE: Deduct .4 if alignment is also performed. NOTE: Manufacturer recommends removal of Rack and Pinion Steering Gear when replacing I
(Combination) – YAW RATE SENSOR – Calibrate
SUSAN C. gave our service a 5 star review on 7/26/2022
Changed Motor Oil & Replaced Filter, Added REQUIRED QTS VALVOLINE SYNPOWER Motor Oil, Lube Chassis, Check all Fluid Levels
Rotate Tires. Visually inspect tires/brakes. NOTE!!!!! Custom Wheels (NON FACTORY WHEELS) MUST be Re-Torqued After 100 Miles to Manufacturer Specs! Beck Automotive is NOT Liable if Re-Torquing is not done by Beck Automotive Technicians (Complementary Re-Torquing)
Beck Automotive Courtesy Inspection
REGAN H. gave our service a 5 star review on 5/25/2022
CK FOR TUNE UP-FLUID CHANGES (MAINTANCE)—VEH BEEN SETTING FOR PAST 2 YEARS
BG POWER STEERING SERVICE
BG COOLING SYSTEM SERVICE 1 GALLON (4CYL)
AXLE SHAFT ASSEMBLY – Remove & Install or Remove & Replace – Left Side – [DOES NOT include alignment. NOTE: For Independent Suspension Type Axles, Axle Shaft Assembly consists of Axle Shaft, Boots and Joints.]
Changed Motor Oil & Replaced Filter, Added REQUIRED QTS VALVOLINE SYNPOWER Motor Oil, Lube Chassis, Check all Fluid Levels
Rotate Tires. Visually inspect tires/brakes. NOTE!!!!! Custom Wheels (NON FACTORY WHEELS) MUST be Re-Torqued After 100 Miles to Manufacturer Specs! Beck Automotive is NOT Liable if Re-Torquing is not done by Beck Automotive Technicians (Complementary Re-Torquing)
Beck Automotive Courtesy Inspection
BRIAN C. gave our service a 5 star review on 5/17/2022
Changed Motor Oil & Replaced Filter, Added REQUIRED QTS VALVOLINE SYNPOWER Motor Oil, Lube Chassis, Check all Fluid Levels
Rotate Tires. Visually inspect tires/brakes. NOTE!!!!! Custom Wheels (NON FACTORY WHEELS) MUST be Re-Torqued After 100 Miles to Manufacturer Specs! Beck Automotive is NOT Liable if Re-Torquing is not done by Beck Automotive Technicians (Complementary Re-Torquing)
Beck Automotive Courtesy Inspection
GARY P. gave our service a 5 star review on 5/7/2022